Interactive tool

Saltwater Pool Salt Dose Calculator

Estimate pounds of pool salt to raise salinity from current to target ppm. Free calculator — retest and follow your SWG manual.

Estimates only — always retest water and follow product labels. Not professional advice.

Salt dose calculator

Pounds of pool salt to move from current toward target salinity (~6.4 lb / 10k gal / 100 ppm).

Estimates only. Your salt cell manual and a reliable salt test win. Retest after dissolving.

From a salt test or SWG reading.

Often ~3200 ppm — check your SWG.

Estimated amount

204.8 lb

≈ 92.9 kg · 6 × 40 lb bags

To raise salt about 3,200 ppm in 10,000 gal.

  1. Broadcast salt in 2–3 shallow zones (not piled in one spot).
  2. Brush to help dissolve; keep pump running.
  3. Wait ~24 hours, retest salt, then fine-tune.
  • Estimate only — confirm SWG manufacturer target range (often ~2700–3400 ppm).
  • Use pool-grade salt (evaporated / solar). Avoid rock salt with anti-caking junk when the manual forbids it.
  • Add salt in 2–3 zones slowly; brush to dissolve; run pump; retest after 24 hours.

Saltwater basics · What salt to buy

What this tool estimates

Pounds of salt to raise salinity by the gap between your current reading and a target. It does not diagnose a bad cell or low stabilizer.

Before you add salt

  • Confirm volume and a trustworthy salt reading
  • Read the SWG manual for min/max salinity
  • Brush to dissolve; run the pump; retest after ~24 hours

Salt type comparison

Not all pool salt is identical. Differences matter for cell longevity, water clarity, and how fast the salt dissolves:

  • Standard pool salt (NaCl, ≥99% purity). The default. Food-grade or solar-grade is fine. Avoid rock salt or ice-melt salt — too many impurities.
  • Mineral pool salt. Blended with boron or silver for residual algaestatic effect. Works in standard SWGs but is more expensive per bag.
  • Coarse vs fine grain. Fine dissolves faster (a plus for quick raises) but tends to bridge in the bag if stored in humid spaces. Coarse lasts longer in storage and is easier to broadcast across the deep end.
  • Pool salt with metal-stain inhibitors. Useful if you have iron or copper in your fill water. Skip if you don’t — the additives are wasted.

Whichever you choose, verify the label says ≥99% pure sodium chloride with no added iodine or anti-caking agents at levels that could cloud your water.

When the math is wrong

If your salinity reading still doesn’t match your target after a full 24 hours of circulation, check for these:

  • Volume estimate is off. Recalculate with the pool volume calculator — a 10% volume error means a 10% salt error.
  • Test strips are stale. Salt strips have shorter shelf life than pH strips. Replace any open bottle older than 3 months.
  • Salt is settling to the deep end. Brush the bottom to bring undissolved salt into circulation before retesting.
  • SWG cell is scaled. A scaled cell reads normal salinity even when the water is low — clean per your manual and retest.

For SWG owners, a salt-for-saltwater-pools buying guide helps avoid products that add iron or phosphates to the water.

Adding salt — best practice

  1. Test first. Confirm the actual current ppm with a fresh strip or your SWG’s built-in sensor.
  2. Calculate the gap. Use the calculator above. Don’t overshoot.
  3. Broadcast in the deep end. Pour slowly while walking the deep end so the salt dissolves in the heaviest water.
  4. Brush to dissolve. Any piles left on the floor won’t register until they dissolve.
  5. Run the pump 24 hours. Retest before adding more.

If your SWG is showing a low-salt warning immediately after a dose, give it a full 24 hours of circulation before assuming the dose was short. Most warnings clear once the salt fully mixes.

Storage and shelf life

Pool salt is essentially rock that absorbs water slowly. Store bags off the ground on a pallet or platform, in a dry shed if possible. Salt clumps from humidity are usable but slower to dissolve. Avoid storing near fertilizers or acids — cross-contamination can react and ruin nearby equipment.

How a salt chlorine generator actually works

A salt chlorine generator (SWG) doesn’t hold chlorine in the water. It manufactures it.

The cell holds brine at a few thousand ppm of salt, and a low voltage current splits that salt into chlorine and hydrogen. The chlorine dissolves into the pool and does the same job any other sanitizer would. The cell’s output scales with how much salt it has to work with, which is why a cell in low-salt water complains loudly and a cell in over-salted water wears out early.

Two numbers matter, and both come from your manual rather than from a website:

  • Minimum salinity. Below it, the cell either warns or stops producing.
  • Maximum salinity. Above it, the cell runs hot and its life shortens.

Most manufacturers land somewhere between 2,700 and 4,500 ppm for normal operation. Read yours before you dose.

The math, step by step

For pure sodium chloride, one pound of salt raises salinity by about 12 ppm in 10,000 gallons of water. That gives a simple formula:

pounds of salt = (ppm you need to add x pool gallons) / 120,000

Worked example: a 15,000-gallon pool sitting at 2,200 ppm, heading for 3,500 ppm.

(1,300 ppm x 15,000 gallons) / 120,000 = 162.5 pounds

That’s about four 40-pound bags. Add them in stages, brush each one into the deep end, and let the pump run for 24 hours between bags so the salt dissolves instead of sitting on the floor.

Check the volume first, too. A 10% volume error means 10% more salt than you needed, or 10% less than you thought you were adding.

What changes your salt level afterwards

Salt doesn’t leave the way chlorine does, so it’s worth tracking:

  • Evaporation takes pure water out of the pool and leaves the salt behind, which means salinity climbs over a hot week. Top up with plain water — never with more salt.
  • Rain and fill water dilute it. Municipal water carries a little salt of its own, so a full drain and refill can leave you lower than you expect.
  • Backwashing and splash-out remove salt along with the water, though usually not much of it.
  • The salt cell loses nothing. The salt it consumes becomes chlorine and hydrogen, and the hydrogen leaves as gas.

So the number you set at the start of the season drifts. A monthly salt test is enough for most pools; twice a month through peak summer is better.

Where not to put salt

  • Broadcast it across the deep end rather than piling it in one spot. Undissolved salt left in a heap can leave a bleached patch on a vinyl liner and it stresses fittings.
  • Keep it off the walls and steps while it dissolves, and brush it down into the water.
  • Never add salt through the skimmer, a chlorinator, or a floater. Salt that dissolves in one concentrated spot makes a brine that damages plastic.
  • Keep the generator off until the salt is fully dissolved. Twenty-four to 48 hours of circulation is the usual wait, and running a cell in salty but undissolved water can damage it.
  • Seal the bags. Salt that takes on moisture clumps in the bag and dissolves slowly, which makes the next dose harder to measure.

Frequently Asked Questions

What target should I use?

Whatever your salt chlorine generator manual specifies — often around 2700–3400 ppm. Don’t chase a random internet number.

Bag size?

The tool also shows an approximate count of 40 lb bags for convenience.